Schmidt Metal Map — Which Sections Get Metal

1 · The two options

Owner-corrected structure (Mitch, 2026-08-10): two options only — the old three-option ladder and its “Section B/C/D” taxonomy are retired. Both options are the same roof system (Owens Corning Duration over full-deck Titanium PSU30, copper at every ridge); Option 2 additionally rebuilds the owner-picked facets in 26-gauge concealed-fastener metal.

Option 1 · The Complete Roof

Complete Shingle Roof

$24,100

Baseline · no accent metal

Everything in shingle — including the side deck: the old metal that was laid over the shingles on that run comes off with everything else, and the whole deck gets the same membrane and the same shingles as the rest of the roof.

MAIN FIELD

SIDE DECK

SUNROOM

VISORS

Schematic scope chips — not roof positions, not to scale

Option 2 · The Metal Package

Shingle + Metal Package

$31,800

+$7,700 over Option 1 — measured-basis adder: 461 sq ft (4.61 SQ) at the metal_t1 50% GM floor ($7,650), then clean-splits rounding so every 10/45/45 payment is a whole dollar. Adder GM 50.33%.

Option 1, plus metal on the long side deck over the lower wall including the stair cover — the run that already has old metal laid over the shingles — plus the enclosed back-porch (sunroom) roof. Facets E + C + D (377 sq ft) + G (84 sq ft). Front visors H/I and both mains stay shingle.

MAIN FIELD

SIDE DECK

SUNROOM

VISORS

Schematic scope chips — not roof positions, not to scale

Duration shingle over full-deck PSU30 26-ga concealed-fastener accent metal (profile/finish not yet selected)

2 · The measured roof — all nine Roofr facets, colored by metal section

Traced from the diagram pages of the verified May 16, 2026 Roofr report (SHA-256 matches the measurement receipt). Facet areas, pitches, and drainage arrows are exactly as Roofr printed them; Roofr labels its 2/12 facets “Flat.” Letters A–I are Mitch's annotation of this diagram, and the colors code the owner-corrected metal scope (green box below): orange = the continuous side deck (E + C + D, one metal run), amber = the sunroom roof (G), gray = Duration shingle in both options.

Continuous side deck — facets E + C + D · one metal run over the lower wall including the stair cover · 377 sq ft measured · old metal laid over shingle on part of this deck (owner-confirmed) Sunroom roof — facet G · the enclosed back-porch roof · 84 sq ft measured · its own setup/trim section Stays shingle — facets A, B, F, H, I · both mains, the north-band middle plane, and the front visor planes flanking the front gable Metal total: 461 sq ft = 4.61 SQ measured (side deck 377 + sunroom 84), 2 sections for setup/trim. Letters = Mitch's annotated Roofr diagram (owner-confirmed 2026-08-10). Numbers = Roofr rounded facet areas (sq ft). Arrows = drainage direction as printed by Roofr. Pitches: A 2/12 · B 2/12 · C 2/12 · D 2/12 · E 10/12 · F 10/12 · G 5/12 · H 10/12 · I 10/12.

Whole-roof totals (controlling): 2,168 sq ft / 21.68 SQ · eaves 143′10″ · rakes 162′1″ · ridges 92′5″ · valleys 43′0″ · wall flashing 22′11″ · step flashing 90′8″ · hips 0. All-shingle order basis 24.3 SQ (21.68 × 1.12).

Trace note: shapes follow the Roofr diagram pages; Roofr states “Measurements in diagram are rounded up for display” and its rounded facet values must not be summed as exact order area (exact 2,168 sq ft controls). Fine interior line detail is simplified where the report is ambiguous at this scale. Per Mitch (2026-08-10), the long side strip (E) and the stair-cover planes (C, D) are one continuous deck in the field — the trace shows Roofr's simplified facet outlines, not the physical break lines.

✓ OWNER-CONFIRMED 2026-08-10 — Mitch corrected the scope from his annotated site photos, and the metal now prices on measured areas.

Confirmed by Mitch on 2026-08-10 via photo annotations + decision dialog, working from his annotated copy of the traced Roofr diagram (facet letters his, areas from the Roofr area page). The July “Section B / C / D” taxonomy is retired — in Mitch's words:

“There is no low-slope metal. There's just the facets we're quoting metal for.”— Mitch, 2026-08-10, photo annotations + decision dialog

The long side strip (E) and the stair-cover (C + D) are one continuous deck — old metal was laid directly over shingle on part of it, so part of E shows metal and part shows shingle today. Metal scope: the full continuous side deck (E+C+D = 377 sq ft) plus the rear sunroom roof (G = 84 sq ft) = 461 sq ft = 4.61 SQ, 2 sections for setup/trim. Front visors H/I and both mains stay shingle. Metal-over-shingle layering on the side deck is owner-confirmed; a second layer on the main roof stays a change-order possibility at the printed $185/sq rate.— Mitch, same confirmation

Pricing rule: base stays $24,100; the metal adder reprices on the MEASURED area at the metal_t1 50% GM floor (adder COGS ÷ 0.50, rounded up to the nearest $50 = $7,650), then rounds up to $7,700 under the clean-splits rule so every 10/45/45 payment is a whole dollar. Two options only: $24,100 / $31,800.— Mitch-approved reprice + clean-splits rule, same dialog; implemented in ketron-quote jobs/gary-schmidt/metal_reprice.py

What this closes out:

B-04 (metal sections never measured) — resolved: the metal scope carries Roofr-measured areas under the owner-corrected facet mapping. The old 1.5 / 3.0 SQ draft allowances are retired.
B-01 (expanded adder GM 39.11%, below the metal_t1 50% floor) — resolved: the package adder prices at the 50% floor on measured COGS ($3,824.51 → $7,700 = 50.33% GM, ≥ 50%).
Second-layer question on the side deck — no longer a “maybe”: the metal-over-shingle layering there is owner-confirmed and comes off in the tear-off under both options.
Ladder: July three-option draft (dead taxonomy, adders $2,900 / $4,800 on allowances) → allowance-basis floor (adders $3,050 / $5,850) → owner-corrected two-option final: $24,100 / $31,800.

3 · The metal scope in photos

Authentic CompanyCam field photos (original captions preserved), re-read under the owner-corrected 2026-08-10 mapping. All three show the continuous side deck (E + C + D) — the old “Section B/C/D” identities stamped on them by the July record are retired. The sunroom roof (facet G) has no dedicated scope photo on file. Letter badges = facets.

Section B: existing rectangular galvanized metal roof section

CompanyCam: “Existing rectangular galvanized metal roof section” — corrected reading: the stretch of the side deck where old metal was laid directly over the shingles

The metal-over-shingle run — part of the side deck

The visible metal here is old metal laid directly over shingle on part of the continuous side deck (owner-confirmed 2026-08-10) — which is why part of the run shows metal and part shows shingle today. It all comes off in the tear-off under both options; Option 2 rebuilds the whole deck in new 26-gauge concealed-fastener metal.

Option 1: shingle Option 2: METAL

MEASURED — part of the continuous side deck (E + C + D, 377 sq ft; E alone 298 sq ft @ 10/12 per Roofr). Owner-corrected mapping 2026-08-10; the July “Section B / 1.5 SQ galvanized-rectangle” reading is retired.

Section C: existing stair and porch gabled roof section

C·D

CompanyCam: “Existing stair and porch gabled roof section” — yellow outline + “Needs Plywood Sheathing” are CompanyCam field annotations. Corrected reading: the stair-cover planes, continuous with the side deck.

The stair cover — twin planes of the same deck

The twin stair-cover planes (facets C + D). Per Mitch, these are not a separate little roof — they are the same continuous deck as the long side strip (E), and the metal package covers the whole run with no shingle/metal split. The base scope's up-to-two-sheet sheathing allowance lives here.

Option 1: shingle Option 2: METAL

MEASURED — facets C + D, 79 sq ft combined (36 + 43), both 2/12 per Roofr; part of the 377 sq ft continuous side deck. Owner-corrected mapping 2026-08-10; the July 3.0 SQ B+C+D allowance is retired.

Section D: existing long eyebrow roof above lower wall

CompanyCam: “Existing long eyebrow roof above lower wall” — corrected reading: the long side deck over the lower wall (facet E), seen end-on from the yard

The long side deck — the full run from the yard

The long run above the lower wall — facet E, 298 sq ft, the biggest piece of the metal package. In Option 2 the whole continuous deck (this run plus the stair cover) becomes matching 26-gauge concealed-fastener metal, end-to-end. The front visor planes (H, I) flanking the front gable are NOT part of this run and stay shingle.

Option 1: shingle Option 2: METAL

MEASURED — facet E, 298 sq ft @ 10/12 per Roofr; with the stair cover, the continuous deck totals 377 sq ft. Owner-corrected mapping 2026-08-10; the July “Section D eyebrow” reading (and its allowance basis) is retired.

4 · Facet-by-option matrix

Roof area	What it is (owner-corrected 2026-08-10)	Facets / pitch	Option 1 $24,100	Option 2 $31,800	Dimension status
Main roof field	Both mains and the north-band middle plane — whole deck gets Titanium PSU30 + Owens Corning Duration in both options, plus copper strip at all ridges	A 727 + B 792 @ 2/12; F 91 @ 10/12	SHINGLE	SHINGLE	Measured — Roofr, May 16 2026: whole roof 2,168 sf / 21.68 SQ / 9 facets; order basis 24.3 SQ
Continuous side deck long run over the lower wall + stair cover	ONE continuous deck (owner-confirmed): the long side strip and the stair-cover planes. Old metal laid directly over shingle on part of it — comes off in the tear-off either way. 2-sheet sheathing allowance lives at the stair cover.	E 298 @ 10/12; C 36 + D 43 @ 2/12	SHINGLE old metal + shingle come off, deck sealed, shingled	METAL	Measured — 377 sq ft (owner-corrected mapping 2026-08-10)
Sunroom roof enclosed back porch	The rear sunroom (enclosed back-porch) roof — its own setup/trim section in the metal package	G 84 @ 5/12	SHINGLE	METAL	Measured — 84 sq ft (owner-corrected mapping 2026-08-10)
Front visors flanking the front gable	The two visor planes on the front of the house — stay shingle in both options (owner-picked scope excludes them)	H 53 + I 48 @ 10/12	SHINGLE	SHINGLE	Measured — 101 sq ft combined; not in the metal scope

Metal system in Option 2: 26-gauge concealed-fastener standing-seam design intent; exact profile (1.5″ vs 1.75″ snap-lock), coverage, finish, and color are deliberately unselected — “the metal finish is picked off the manufacturer's standard color card… with real chips in hand.” Customer sees a fixed-price package.

Status of the old caveats: BLOCKERS.md B-04 (“Sections B, C and D have never been measured”) and the metal BOM's fail-closed UNKNOWN quantities are closed by the owner-corrected mapping — the metal scope now carries Roofr-measured areas (461 sq ft total) and the adder prices on them at the metal_t1 50% floor. The metal-over-shingle layering on the side deck is owner-confirmed and included in the scope reading; a second shingle layer on the main roof remains a change-order possibility at the printed $185/sq rate. Edge dimensions still get a routine field check before the material order, but pricing no longer rides on an allowance.